0x10 Hotcue7 Right - 0x20 Hotcue8 Right - 0x40 GNT - 0x80 MIC 0x01 Hotcue3 Right - 0x02 Hotcue4 Right - 0x04 Hotcue5 Right - 0x08 Hotcue6 Right 0x10 Cue Right - 0x20 Play Right - 0x40 Hotcue1 Right - 0x80 Hotcue2 Right 0x01 Hotcues Right - 0x02 Samples Right - 0x04 Sync Right - 0x08 Keylock Right 0x10 Prepation Right - 0x20 Browse View Right - 0x40 Grid Right - 0x80 Shift Right 0x01 Phones Left - 0x02 Phones Right - 0x04 Rev Right - 0x08 FLX Right 0x10 FX Select1 - 0x20 FX Select2 - 0x40 FX Select3 - 0x80 FX Select4 0x01 Hotcue5 Left - 0x02 Hotcue6 Left - 0x04 Hotcue7 Left - 0x08 Hotcue8 Left 0x10 Hotcue1 Left - 0x20 Hotcue2 Left - 0x40 Hotcue3 Left - 0x80 Hotcue4 Left 0x01 Sync Left - 0x02 Keylock Left - 0x04 Cue Left - 0x08 Play Left 0x10 Grid Left - 0x20 Shift Left - 0x40 Hotcues Left - 0x80 Samples Left 0x01 Rev Left - 0x02 FLX Left - 0x04 Prepation Left - 0x08 Browse View Left Represents the state of the buttons and the jog wheels, while reportIDĠx2 is about the scalers. Usage Page (FF01h), FF01h, vendor-defined $> usbhid-dump -d17cc:1710 | grep -v : | xxd -r -p | hidrd-convert -o spec Show the current instantaneous deck volumeĪdjusts the crossfader between both decks Quick effect superknob for the corresponding deckĪdjusts the pregain for all the sample decks combinedĪdjusts the cue/main mix in the headphone outputĮnable or disable effect units for both decksĪdjusts the channel volume fader for the corresponding deck Toggles microphone talkover, long press for permanent activation Otherwise eject trackĪdjusts the hardware gain - it is unlinked to the software main gain since v2.3 If track is playing, CUE default behaviour. If track is loaded into corresponding slot, go to CUE point and play If hotcue is set, seeks the player to hotcue position. Seeks a player to the start and then stops it If the CUE point is set, jump to it and stops Once disabled, playback will resume where the track would have been if it had not entered the loopĪctivate current loop, jump to its loop in point, and stop playbackĬontrol scratching when touched from the top (Missing: temporarily bend the pitch when touched from the side)Īdjust beatgrid so closest beat is aligned with the current play positionĪdjust beatgrid to match another playing deckĪctivates secondary functions when pressed Set a loop of the defined number of beats and enables the loopĪctive sampler mode (for the number buttons)Īctivate hotcue mode (for the number buttons)Īctivates a rolling loop of the defined number of beats. Syncs the phase to that of the other track Press longer to activate master sync on that deck. Syncs the BPM and phase (depending on quantize). Since v2.3 the Master knob is intentionally not linked to Mixxx's Main Gain, following NI's suggestions.Īdd selected track to AutoDJ queue (bottom) Have a look at the corresponding thread in the forums for questions and HINT: Since this controller is a USB-HID device, you might need to set the corresponding udev rules in Linux. Has no impact on the output level or LED brightness ( as opposed to the MK2). The Kontrol S2 MK3Ĭan run from USB bus power, and using a separate power supply Signals from a computer, so it can work with Mixxx. The MK3 uses the standard HID protocol to send and receive Headphone outputs (1/8" / 3.5 mm TRS) and microphone inputs (1/4" / 6.3 It has two integrated stereo outputs (line and 1/8" / 3.5 mm TRS), The Kontrol S2 MK3 is a two-channel controller with an integrated soundĬard. Native Instruments Traktor Kontrol S2 MK3
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |